Speaker enrollment functionSpeaker enrollment function  - Bluetooth® 2.0 interface - For pleasant driving - Mitsubishi Lancer Owner's Manual - Mitsubishi Lancer

The Bluetooth® 2.0 interface can use the speaker enrollment function to create a voice model for one person per language.

This makes it easier for the Bluetooth® 2.0 interface to recognise voice commands said by you.

You can turn a voice model registered with the speaker enrollment function on and off whenever you want.

Speaker enrollment

It takes about 2 to 3 minutes to complete the speaker enrollment process.

To ensure the best results, run through the process while in the driver’s seat, in an environment that is as quiet as possible (when there is no rain or strong winds and the vehicle windows are closed). Please turn off your phone while in speaker enrollment to prevent interruption of the process.

Use the following procedure for speaker enrollment.

1. Stop your vehicle in a safe area, put the gearshift lever (M/T) in the “N” (Neutral) position, or the selector lever (CVT) or gearshift lever (Twin Clutch SST) in the “P” (PARK) position, and pull the parking brake lever.

► Speaker enrollment is not possible unless the vehicle is parked. Make sure Note

► Speaker enrollment is not possible unless the vehicle is parked. Make sure you park the vehicle in a safe area before attempting speaker enrollment.

2. Press the SPEECH button.

3. Say “Voice training”.

4. The voice guide will say “This operation must be performed in a quiet environment while the vehicle is stopped. See the owner’s manual for the list of required training phrases.

Press and release the SPEECH button when you are ready to begin. Press the HANGUP button to cancel at any time”.

Press the SPEECH button to start the speaker enrollment process.

► If you do not start the speaker enrollment process within 3 minutes of pressing Note

► If you do not start the speaker enrollment process within 3 minutes of pressing the SPEECH button, the speaker enrollment function will time out.
The voice guide will say “Speaker Enrollment has timed out”. The system will then beep and the voice recognition mode will be deactivated.

5. The voice guide will prompt for phrase 1. Repeat the corresponding phrase listed in table “Enrollment commands”.

The system will register your voice and then move on to the registration of the next command.

Continue the process until all phrases have been registered.

► To repeat the most recent voice training command, press and release the SPEECH Note

► To repeat the most recent voice training command, press and release the SPEECH button.
► If you press the HANG-UP button anytime during the process, the system will beep and stop the speaker enrollment process.

6. When all enrollment commands have been read out, the voice guide will say “Speaker enrollment is complete”. The system will then end the speaker enrollment process and return to the main menu.

► Completing the speaker enrollment process will turn on the voice model automatically. Note

► Completing the speaker enrollment process will turn on the voice model automatically.
► The commands “Help” and “Cancel” will not work in this mode.

Enabling and disabling the voice model and retraining

You can turn a voice model registered with the speaker enrollment function on and off whenever you want.

You can also retrain the system.

Use the following procedure to perform these actions.

1. Press the SPEECH button.

2. Say “Voice training”.

3. If you have completed a speaker enrollment process once already, the voice guide will say either “Enrollment is enabled. Would you like to disable or retrain?” or “Enrollment is disabled. Would you like to enable or retrain?” 4. When enrollment is “enabled”, the voice model is on; when enrollment is “disabled”, the voice model is off. Say the command that fits your needs.

Say “Retrain” to start the speaker enrollment process and recreate a new voice model. (Refer to “Speaker enrollment”.)

    See also:

    Changing the momentary fuel consumption display (Type 2)
    It is possible to change the bar graph setting of the momentary fuel consumption display. 1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setti ...

    New frontier
    During the course of 2012, MMC will also take advantage of the built-in possibilities of Mitsubishi Outlander's versatile platform & powerful electronic architecture to add an EV-based plug-In ...

    Handling of compact discs
    • Use only the type of compact discs that have the mark shown in the illustration below. (Playback of CD-R or CD-RW discs may cause problems.) • The use of special shaped, damaged compact di ...