Changing the function settings (when the ignition switch or the operation mode is ON)Changing the function settings (when the ignition switch or the operation 
mode 
is ON)  - Multi-information display - Instruments and controls - Mitsubishi ASX Owner's Manual - Mitsubishi ASX

1. Stop the vehicle in a safe place.

Firmly apply the parking brake and put the gearshift lever into the “N” (Neutral) position (M/T) or the selector lever into the “P” (PARK) position (CVT).

2. Lightly press the multi-information meter switch a few times to switch the information screen to the function setting screen.

Refer to “Information screen (when the ignition switch or the operation mode is ON)”.

CAUTION

• For safety, stop the vehicle before operating. CAUTION

• For safety, stop the vehicle before operating.

While driving, even if you operate the multi- information meter switch, the function setting screen is not displayed.

3. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.

NOTE

• To return the menu screen to the function setting screen, press and hold the NOTE

• To return the menu screen to the function setting screen, press and hold the multi-information meter switch for about 2 seconds or more.

• If no operations are made within about 15 seconds of the menu screen being displayed, the display returns to the function setting screen.

4. Select the item to change on the menu screen and change to the desired setting. Refer to the following items for further details on the operation methods.

Changing the reset mode for average fuel consumption and average speed

The mode conditions for the average fuel consumption and average speed display can be switched between “Auto reset” and “Manual reset”.

1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.

Refer to “Changing the function settings (when the ignition switch or the operation mode is ON)”.

2. Lightly press the multi-information meter switch to select “AVG” (average fuel consumption and average speed setting).

3. Press and hold the multi-information meter switch for about 2 seconds or more

3. Press and hold the multi-information meter switch for about 2 seconds or more to switch in sequence from A (Auto reset mode) → M (Manual reset mode) → A (Auto reset mode).

The setting is changed to the selected mode condition.

Manual reset mode

• When the average fuel consumption and average speed are being displayed, if you hold down the multi-information meter switch, the average fuel consumption and average speed displayed at that time are reset.

• When the following operation is performed, the mode setting is automatically switched from manual to auto.

[Except for vehicles equipped with keyless operation system]

Turn the ignition switch from the “ACC” or “LOCK” position to the “ON” position.

[For vehicles equipped with the keyless operation system]

Change the operation mode from ACC or OFF to ON.

Switching to auto occurs automatically.

If switching to manual mode is done, however, the data from the last reset is displayed.

Auto reset mode

• When the average fuel consumption and average speed are being displayed, if you hold down the multi-information meter switch, the average fuel consumption and average speed displayed at that time are reset.

• When the engine switch or the operation mode is in the following conditions, the average fuel consumption display and average speed display are automatically reset.

[Except for vehicles equipped with keyless operation system]

The ignition switch is in the “ACC” or “LOCK” position for about 4 hours or longer.

[For vehicles equipped with keyless operation system]

The operation mode is in ACC or OFF for about 4 hours or longer.

• The average fuel consumption display and average speed display can be reset NOTE

• The average fuel consumption display and average speed display can be reset individually for the auto reset mode and manual reset mode.

• The memory of the auto reset mode or manual reset mode for the average fuel consumption display and average speed display is erased if the battery is disconnected.

• The initial (default) setting is “Auto reset mode”.

Changing the fuel consumption display unit

The display unit for fuel consumption can be switched.

The distance, speed, and amount units are also switched to match the selected fuel consumption unit.

1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.

Refer to “Changing the function settings (when the ignition switch or the operation mode is ON)”.

2. Lightly press the multi-information meter switch to select “AVG UNIT” (fuel consumption display setting).

3. Press and hold the multi-information meter switch for about 2 seconds or more

3. Press and hold the multi-information meter switch for about 2 seconds or more to display “AVG UNIT” (fuel consumption display unit setting).

4. Lightly press the multi-information meter switch to switch in sequence from km/L →

L/100 km → mpg (US) → mpg (UK) → RETURN → km/L.

5. Press and hold the multi-information meter switch for about 2 seconds or more

5. Press and hold the multi-information meter switch for about 2 seconds or more to change the setting to the selected unit.

• The display units for the driving range, the average fuel consumption, the NOTE

• The display units for the driving range, the average fuel consumption, the average speed and the momentary fuel consumption are switched, but the units for the indicating needle (speedometer), the odometer and the tripmeter will remain unchanged.

• The memory of the unit setting is erased if the battery is disconnected, and it returns automatically to L/100 km.

The distance and speed units are also switched in the following combinations to match the selected fuel consumption unit.

Changing the temperature unit

Changing the temperature unit

The display unit for temperature can be switched.

1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.

Refer to “Changing the function settings (when the ignition switch or the operation mode is ON)”.

2. Lightly press the multi-information meter switch to select (temperature unit setting).

3. Press and hold the multi-information meter switch for about 2 seconds or more

3. Press and hold the multi-information meter switch for about 2 seconds or more to switch in sequence from °C → °F → °C.

The setting is changed to the selected temperature unit.

• If the battery is disconnected, the unit setting is erased from memory and NOTE

• If the battery is disconnected, the unit setting is erased from memory and is automatically set to °C.

Changing the display language

The language of the multi-information display can be switched.

1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.

Refer to “Changing the function settings (when the ignition switch or the operation mode is ON)”.

2. Lightly press the multi-information meter switch to select “LANGUAGE” (language setting).

3. Press and hold the multi-information meter switch for about 2 seconds or more

3. Press and hold the multi-information meter switch for about 2 seconds or more to display “LANGUAGE” (language setting).

4. Lightly press the multi-information meter switch to switch in sequence from JAPANESE → ENGLISH → GERMAN → FRENCH → SPANISH → ITALIAN → “---” (do not display warning message) → RETURN → JAPANESE.

5. If you hold down the multi-information meter switch for about 2 seconds or

5. If you hold down the multi-information meter switch for about 2 seconds or more, the setting is changed to the selected language.

• The memory of the language setting is erased if the battery is disconnected, NOTE

• The memory of the language setting is erased if the battery is disconnected, and it returns automatically to ENGLISH.

• If “---” is selected in the language setting, a warning message is not displayed when there is a warning display or interrupt display.

Changing the language cooperative control

The language used in MITSUBISHI Multi-Communication System (MMCS) (if so equipped) or the Bluetooth® 2.0 interface (if so equipped) can be changed automatically to the same language as that shown in the multi-information display.

1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.

Refer to “Changing the function settings (when the ignition switch or the operation mode is ON)”.

2. Lightly press the multi-information meter switch to select (language cooperative control).

3. Press and hold the multi-information meter switch to switch in sequence from

3. Press and hold the multi-information meter switch to switch in sequence from A (language cooperation enabled) → M (language cooperation disabled) → A (language cooperation enabled).

The setting is changed to the selected condition.

• The memory of the language cooperative control is erased if the battery is NOTE

• The memory of the language cooperative control is erased if the battery is disconnected, and it returns automatically to A (language cooperation enabled).

• The language display modified with the language setting can be switched in the following manner.

• When A (language cooperation enabled) has been selected with the language cooperative control, the language for MITSUBISHI Multi-Communication System (MMCS) (if so equipped) or the Bluetooth® 2.0 interface (if so equipped) is automatically changed to the language selected for the multi-information display.

• When M (language cooperation disabled) has been selected with the language cooperative control, the language for MITSUBISHI Multi-Communication System (MMCS) (if so equipped) or the Bluetooth® 2.0 interface (if so equipped) is not automatically changed to the language selected for the multi-information display.

Operation sound setting

You can turn off the operation sounds of the multiinformation meter switch and daytime dipper button.

1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.

Refer to “Changing the function settings (when the ignition switch or the operation mode is ON)”.

2. Lightly press the multi-information meter switch to select (operation sound setting).

3. Press and hold the multi-information meter switch for about 2 seconds or more

3. Press and hold the multi-information meter switch for about 2 seconds or more to switch in sequence from ON (operation sound on) → OFF (operation sound off) → ON (operation sound on).

The setting is changed to the selected condition.

• The memory of the operation sound setting is erased if the battery is disconnected, NOTE

• The memory of the operation sound setting is erased if the battery is disconnected, and it returns automatically to ON (operation sound on).

• The operation sound setting only deactivates the operation sound of the multi-information meter switch and daytime dipper button. The warning display and other sounds cannot be deactivated.

Changing the time until “REST REMINDER” is displayed

The time until the display appears can be changed.

1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.

Refer to “Changing the function settings (when the ignition switch or the operation mode is ON)”.

2. Lightly press the multi-information meter switch to select “ALARM” (rest time setting).

3. Press and hold the multi-information meter switch for about 2 seconds or more

3. Press and hold the multi-information meter switch for about 2 seconds or more to display “ALARM” (rest time setting).

4. Lightly press the multi-information meter switch to select the time until

4. Lightly press the multi-information meter switch to select the time until the display.

5. Press and hold the multi-information meter switch for about 2 seconds or more, the setting is changed to the selected time.

• If the battery is disconnected, the unit setting is erased from memory and NOTE

• If the battery is disconnected, the unit setting is erased from memory and is automatically set to OFF.

• The drive time is reset when the ignition switch is turned off or the operation mode is put in OFF.

Changing the turn-signal sound

It is possible to change the turn-signal sound.

1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.

Refer to “Changing the function settings (when the ignition switch or the operation mode is ON)”.

2. Lightly press the multi-information meter switch to select (changing the turn-signal sound).

3. Press and hold the multi-information meter switch for about 2 seconds or more

3. Press and hold the multi-information meter switch for about 2 seconds or more to switch in sequence from 1 (turn-signal sound 1) →

2 (turn-signal sound 2) → 1 (turn-signal sound 1).

The setting changes to the selected turn-signal sound.

Changing the momentary fuel consumption display (Type 2)

It is possible to change the bar graph setting of the momentary fuel consumption display.

1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.

Refer to “Changing the function settings (when the ignition switch or the operation mode is ON)”.

2. Lightly press the multi-information meter switch to select display) (changing the momentary fuel consumption display)

3. Press and hold the multi-information meter switch for about 2 seconds or more

3. Press and hold the multi-information meter switch for about 2 seconds or more to switch in sequence from ON (with the green bar graph) → OFF (without the green bar graph) → ON (with the green bar graph).

The setting changes to the selected bar graph setting.

Returning to the factory settings

All of the function settings can be returned to their factory settings.

1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.

Refer to “Changing the function settings (when the ignition switch or the operation mode is ON)”.

2. Lightly press the multi-information meter switch to select “RESET” (returning to the factory settings).

3. When you press and hold the multi-information meter switch for about 5 seconds

3. When you press and hold the multi-information meter switch for about 5 seconds or more, the buzzer sounds and all of the function settings are returned to the factory settings.

• The factory settings are as follows. NOTE

• The factory settings are as follows.

• Average fuel consumption and average speed reset mode: A (Auto reset)
• Fuel consumption display unit: L/100 km
• Temperature unit: °C (Celsius)
• Display language: ENGLISH
• Cooperative language setting: A
• Operation sounds: ON (Operation sounds on)
• “REST REMINDER” display: OFF
• Turn-signal sound: Turn-signal sound 1
• Momentary fuel consumption with the green bar graph (Type 2): ON

    See also:

    Pricing & Features
    The Lancer GT's standard features include a USB input and Bluetooth for the $20,790 starting price with a manual transmission, $21,790 with the automatic (all prices include destination charges). ...

    Damaged paint
    Small cracks and scratches in the paint coat should be touched up as soon as possible with MITSUBISHI touch-up paint to prevent corrosion. Check body areas facing the road or the tyres carefully fo ...

    Electric window control
    The electric windows can only be operated with the ignition switch in the “ON” position or the operation mode in ON. WARNING • Before operating the electric window control, make sure that n ...