To operate using the keyless operation functionTo operate using the keyless operation function  - Keyless operation system - Locking and unlocking - Mitsubishi ASX Owner's Manual - Mitsubishi ASX

Locking the doors and tailgate

When you are carrying the keyless operation key, if you press the driver’s or front passenger’s door lock/unlock switch (A), or the tailgate LOCK switch (B) within the operating range, the doors and the tailgate are locked.

The turn-signal lamps will blink once.

Also refer to “Locking and unlocking: Doors, Central door locks, tailgate” on pages 1-21, 1-22 and 1-26.

NOTE

• For vehicles equipped with the mirror retractor switch, the outside rear-view NOTE

• For vehicles equipped with the mirror retractor switch, the outside rear-view mirrors automatically retract when all the doors and tailgate are locked using the keyless operation function.

Refer to “Starting and driving: Outside rearview mirrors”.

• With a vehicle that has a Dead Lock System, pressing the driver’s or front passenger’s door lock/unlock switch (A), or the tailgate LOCK switch (B) two times in succession causes the Dead Lock System to be set. (Refer to “Setting the system”).

• The keyless operation function does not operate under the following conditions:
• The keyless operation key is inside the vehicle.
• A door or the tailgate is open or ajar.
• The operation mode is not in OFF.

Unlocking the doors and tailgate

When you are carrying the keyless operation key, if you press the driver’s or front passenger’s door lock/unlock switch (A), or the tailgate OPEN switch (B) within the operating range, all the doors and the tailgate are unlocked.

If the front room lamp switch is in the “DOOR” position or the rear room lamp switch (except for vehicles equipped with the sunshade) is in the middle (•) position at this time, the room lamp will turn on for 15 seconds. The turn-signal lamps will blink twice.

If the driver’s or front passenger’s door lock/unlock switch is pressed and any of the doors or tailgate is not opened within approximately 30 seconds, relocking will automatically occur. Also refer to “Locking and unlocking: Doors, Central door locks, tailgate” on pages 1-21, 1-22 and 1-26.

NOTE

• For vehicles equipped with the mirror retractor switch, the outside rear-view NOTE

• For vehicles equipped with the mirror retractor switch, the outside rear-view mirrors automatically extend when all the doors and tailgate are unlocked using the keyless operation function.

Refer to “Starting and driving: Outside rearview mirrors”.

• Except for vehicles equipped with a Dead Lock System, the keyless operation function can be set so that only the driver’s door unlocks when the driver’s door lock/unlock switch is pressed.

If the keyless operation function is set to work as described above, all the doors and the tailgate unlock when the driver’s door lock/unlock switch is pressed two times in succession.

Refer to “Setting of door and tailgate unlock function”.

• The keyless operation function does not operate under the following conditions:
• The keyless operation key is inside the vehicle.
• A door or the tailgate is open or ajar.
• The operation mode is not in OFF.

• The time between unlocking and automatic locking can be adjusted. Consult a MITSUBISHI MOTORS Authorized Service Point.

On vehicles equipped with MITSUBISHI Multi-Communication System (MMCS), screen operations can be used to make the adjustment.

Refer to the separate owner’s manual for details.

Operation confirmation when locking and unlocking

Operation can be confirmed as shown below. However, the room lamp will only illuminate if the front room lamp switch is in the “DOOR” position or the rear room lamp switch (except for vehicles equipped with the sunshade) is in the middle (•) position.

When locking: The turn-signal lamps will blink once.

When unlocking:

The room lamp illuminates for approximately 15 seconds, the turn-signal lamps blink twice.

• Functions can be modified as stated below. NOTE

• Functions can be modified as stated below.

For further information, please contact your MITSUBISHI MOTORS Authorized Service Point.

On vehicles equipped with MITSUBISHI Multi-Communication System (MMCS), screen operations can be used to make the adjustment.

Refer to the separate owner’s manual for details.

• Set the confirmation function (blinking of the turn-signal lamps) to operate only when the vehicle is locked or only when the vehicle is unlocked.

• Disable the operation confirmation function (blinking of the turn-signal lamps).

• Change the number of blinks for the operation confirmation function (blinks of the turn-signal lamps)

Operation of the Dead Lock System

With a vehicle that has a Dead Lock System, it is possible to set the Dead Lock System using the driver’s or front passenger’s door lock/unlock switch, or the tailgate LOCK switch. (Refer to “Dead Lock System”.)

    See also:

    CD control panel and display
    1- AM/FM button 2- CD (CD mode changeover) button 3- PWR (On-Off) switch 4- PAGE (Title scroll) button 5- DISP (Display) button 6- RPT (Repeat) button 7- RDM (Random) button 8- (Fast-rever ...

    Ventilation slots
    The ventilation slots in front of the windscreen should be brushed clear after a heavy snowfall so that the operation of the heating and ventilation systems will not be impaired. ...

    Headlamps (high/low beam, for vehicles with high intensity discharge headlamps)
    Do not attempt to disassemble or repair headlamps, and do not attempt to replace their bulbs. Warning ► A high voltage is present in the power circuit and in the bulbs and bulb terminals. ...